Overview

Generally, images are stored in flash and then loaded to RAM to boot system, which is called boot from flash. USB boot allows system boot from USB, which means images are stored in and loaded from USB device, such as a U-disk.

Architecture

USB boot can be implemented in the U-Boot phase. Figure below shows the flow to boot from flash and USB. The system is booting from flash by default. To implement USB boot, it is necessary to enable USB function and USB mass storage class in the U-Boot phase to make system recognize USB device. Then using fat command to load images to RAM. Finally, executing bootm command to boot kernel.

../../_images/usb_boot_with_secure_boot_disabled.svg

USB boot with secure boot disabled

There are additional steps when enabling secure boot because images in USB device also need to be verified. For USB boot, images are verified in the phase of bootm. bootm command will return fail If verify fail and system will not start kernel. Please refer to secure boot chapter to get more information about secure boot.

../../_images/usb_boot_with_secure_boot_enabled.svg

USB boot with secure boot enabled

备注

  • User should input any content in time when booting system to enter U-Boot command line mode, or system will boot from flash.

  • USB device must be plugged in board before USB initialization because the USB driver in U-Boot uses polling mode to recognize USB device.

Configuration

To enable USB boot, the following configuration should be enabled for U-Boot. In SDK, these configurations are enabled as default.

CONFIG_PHY=y
CONFIG_PHY_RTK_USB=y
CONFIG_USB_STORAGE=y
CONFIG_USB=y
CONFIG_USB_DWC2=y
CONFIG_USB_DWC2_BUFFER_SIZE=64
CONFIG_USB_HOST=y
CONFIG_DM_USB=y
CONFIG_BOOTDELAY=3
CONFIG_FS_FAT=y
CONFIG_FS_FAT_MAX_CLUSTSIZE=65536
CONFIG_CMDLINE=y
CONFIG_CMD_USB=y
CONFIG_CMD_FAT=y

Usage

USB Boot with Secure Boot Disabled

  1. Put dtb.img and kernel.img in the root directory of U-disk. The U-disk should be fat32 format.

  2. Input any content in time when booting system to enter U-Boot command line mode.

  3. Plug in U-disk.

  4. Input command usb start. U-disk will be recognized with the following log:

    => usb start
starting USB...
Bus usb@40080000: USB DWC2
scanning bus usb@40080000 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found

  5. Input command fatload usb 0 0x60370000 dtb.img and fatload usb 0 0x60380000 kernel.img to load images from U-disk to RAM.

    => fatload usb 0 0x60370000 dtb.img
19423 bytes read in 17 ms (1.1 MiB/s)
=>
=> fatload usb 0 0x60380000 kernel.img
3294376 bytes read in 253 ms (12.4 MiB/s)

  6. Input command usb stop to deinit USB function to prevent kernel’s USB function from being affected.

  7. Input command bootm 0x60380000 - 0x60370000 to boot kernel.

USB Boot with Secure Boot Enabled

  1. Please refer to secure boot chapter to enable and configure secure boot first.

  2. Put secure dtb.img, kernel.img and vbmeta.img in the root directory of U-disk. The U-disk should be fat32 format.

  3. Plug in U-disk.

  4. Input command usb start. U-disk will be recognized with the following log:

    => usb start
starting USB...
Bus usb@40080000: USB DWC2
scanning bus usb@40080000 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found

  5. Input command fatload usb 0 0x60370000 dtb.img, fatload usb 0 0x60380000 kernel.img and fatload usb 0 0x60d80000 vbmeta.img to load images from U-disk to RAM.

    => fatload usb 0 0x60380000 kernel.img
3357648 bytes read in 259 ms (12.4 MiB/s)
=>
=> fatload usb 0 0x60370000 dtb.img
19549 bytes read in 16 ms (1.2 MiB/s)
=>
=> fatload usb 0 0x60d80000 vbmeta.img
5632 bytes read in 14 ms (392.6 KiB/s)

  6. Input command mtd read pk-hash 0x60e80000 0x0 0x1000 to load pk-hash from flash to RAM.

    => mtd read pk-hash 0x60e80000 0x0 0x1000
SPIC mode 0x2000
mtd: partition "pk-hash" doesn't end on an erase block -- force read-only
Reading 4096 byte(s) (2 page(s)) at offset 0x00000000

  7. Input command usb stop to deinit USB function to prevent kernel’s USB function from being affected.

  8. Input command bootm verify 0x60380000 0x60370000 0x60d80000 0x40000 0x60e80000 0x1000 0x60380000 - 0x60370000 to verify and load images from U-disk to RAM. If success, console will show the following log:

    Public Key Hash Verified Success!
VbMeta Signature Verified Success!
Kernel Image verified success!
DTB/FDT Image verified success.

    If fail, console will show the following log:

    Bootm fail! Please verify images correctly.

备注

Since secure boot is implemented by several images together, user should guarantee that when compile the images dtb.img, kernel.img and vbmeta.img, which will be put into U-disk, the images km4_boot_all_en.bin, km0_km4_app_en.bin and rootfs_ubi.img should not be modified.