Introduction

LEDC is used to control external Intelligent LED lamps, like WS2812B.

LEDC supports DMA mode and interrupt mode, with 32*24bit LEDC FIFO. LEDC also supports RGB888 display mode and configurable refresh time.

Architecture

The LEDC driver of Realtek follows Linux framework: led-class.c, led-core.c, led-trigger.c. Pattern trigger is supported by this driver. The LEDC software architecture is illustrated in below.

../../_images/ledc_software_arch.svg — LEDC software architecture

For more details of Linux LEDs system, refer to: https://www.kernel.org/doc/html/v5.4/leds/index.html?highlight=leds.

Implementation

The LEDC driver is implemented as the following files:

Driver location	Introduction
<linux>/drivers/rtkdrivers/ledc/Kconfig	LEDC driver Kconfig
<linux>/drivers/rtkdrivers/ledc/Makefile	LEDC driver Makefile
<linux>/drivers/rtkdrivers/ledc/leds-rtk-ws28xxx.c	LEDC functions.
<linux>/drivers/rtkdrivers/ledc/leds-rtk-ws28xxx.h	LEDC related function declaration, macro definition, structure definition and the other header files quoted.

Configuration

DTS Configuration

The LEDC DTS node is defined in DTS file <dts>/rtl8730e-ocp.dtsi.

ledc: led-controller@41008000 {
   compatible = "realtek,ameba-ws28xxx-led";
   reg = <0x41008000 0x1000>;
   interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
   #address-cells = <1>;
   #size-cells = <0>;
   clocks = <&rcc RTK_CKE_LEDC>;
   rtk,led-nums = <1>;
   dmas = <&dma 5>;
   dma-names = "dma_leds_tx";
   rtk,wait-data-timeout = <0x7FFF>;
   rtk,output-RGB-mode = <0>; // Refer to spec for details.
   rtk,data-tx-time0h = <0xD>;
   rtk,data-tx-time0l = <0x27>;
   rtk,data-tx-time1h = <0x27>;
   rtk,data-tx-time1l = <0xD>;
   rtk,refresh-time = <0x3A97>;
   status = "disabled";
   led@0 {
      label = "common";
      reg = <0x0>;
   };
};

The DTS parameters of LEDC are listed in the following table.

LEDC DTS parameters configuration
Property	Description	Configurable?
compatible	The description of LEDC driver: `realtek, ameba-ws28xxx-led`	No
reg	The hardware address and size for LEDC device: <0x41008000 0x1000>.	No
interrupts	The GIC number of LEDC device: <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>.	No
clocks	The clock of LEDC device: <&rcc RTK_CKE_LEDC>.	No
dmas	DMA channel, refer to DMA application note	Yes
dma-names	DMA channel name	Yes
rtk,led-nums	The led numbers in your hardware. 1 LED, 32 LEDs, 64 or the other.	1~1024
rtk,wait-data-timeout	When the setting time exceeds, LEDC will get an interrupt and software-reset the LEDC device.	1~0x7FFF
rtk,output-RGB-mode	Output RGB mode	Yes
rtk,data-tx-time0h	0-code, High-level time, default by 0xd, t0h = 25ns * (0xd + 1).	Yes
rtk,data-tx-time0l	0-code, Low-level time, default by 0x27, t0l = 25ns * (0x27 + 1).	Yes
rtk,data-tx-time1h	1-code, High-level time, default by 0x27, t1h = 25ns * (0x27 + 1).	Yes
rtk,data-tx-time1l	1-code, Low-level time, default by 0xd, t1l = 25ns * (0xd + 1).	Yes
rtk,refresh-time	Reset time control of LED lamp, the refresh time for one slice. Default as 0x3a97, reset time = 25ns * (0x3a97 + 1).	Yes
status	Whether enable this device. disabled okay	Yes
led@0	LEDC client node. The whole group of ws28xxx LED lamps will be considered as one LED device named `common`.	No

备注

Section LEDC Control Application provides an example for the LEDC timing parameters.

The pin assignments of LEDC are listed in the following table.

Port name	Pin name	pinctrl description
PA3	LEDC_TX	Shall add manually.
PA6	LEDC_TX	<&ledc_pins>
PA7	LEDC_TX	Shall add manually.
PA8	LEDC_TX	Shall add manually.
PA9	LEDC_TX	Shall add manually.
PA10	LEDC_TX	Shall add manually.
PA13	LEDC_TX	Shall add manually.
PA20	LEDC_TX	Shall add manually.
PA21	LEDC_TX	Shall add manually.
PA22	LEDC_TX	<&ledc_pins_a >
PA25	LEDC_TX	<&ledc_pins_a >

LEDC has only one pinmux for Tx, therefore, in pinmux DTS, only one pin is defined. If pinmux needs revision according to the specific board, just revise the ledc_pins node in pinmux DTS. The pinmux can be revised to anyone above, as far as board hardware supported.

Build Configuration

Select Device Drivers -> Drivers for Realtek -> LED driver for WS28XXX.

../../_images/ledc_driver.png — LEDC Driver

APIs

APIs for User Space

Set LEDC pattern:

# cd /sys/class/leds/rtk_ws28xxx:common/
# echo 0x2255FF 0 0x2255FF 0 0x2255FF 0 0x2255FF 0 > hw_pattern

Find the LEDC demo for user space at <sdk>/tests/ledc.

APIs for Kernel Space

None.

LEDC Control Application

Taking WS2812C-2020 LED for example, before using this LED, we have to configure the logical character 0 and character 1 according to the LEDC data input code of typical LED datasheet, as shown in the following table.

Typical LED modulation datasheet
Modulate code	Description	Time range	Unit
T0H	Digital 0 code, high-level time	220 ~ 380	ns
T0L	Digital 0 code, low-level time	580 ~ 1000	ns
T1H	Digital 1 code, high-level time	580 ~ 1000	ns
T1L	Digital 1 code, low-level time	220 ~ 420	ns
RESET	Frame unit, low-level time	> 280	μs

Logical 0 coding time is T0-code: 800ns ~ 1980ns, and logical 1 coding time is T1-code: 800ns ~ 2020ns.

The supported LED number

When LED’s refresh rate is 30 frames/s, the supported LED number is 681 to 1023;
When LED’s refresh rate is 60 frames/s, the supported LED number is 337 to 853.

The related registers of LED setting are LED_T0&T1_TIMING_CTRL_REG, LEDC_DATA_FINISH_CNT_REG, LED_RESET_TIMING_CTRL_REG, LEDC_WAIT_TIME_CTRL_REG, LEDC_DMA_CTRL_REG, and LEDC_INTERRUPT_CTRL_REG.

WS2812 serious LED data transfer protocol uses a single NRZ (non-return zero) communication mode. After the LED power-on reset, the DI port receives data from the controller, the first LED collects initial 24-bit data then sends 24-bit data to the internal data latch, the other data reshaping by the internal signal reshaping amplification circuit sent to the next cascade pixel through the DO port. After transmission of each pixel, the signal reduces 24 bits. Pixel adopts auto reshaping transmit technology, making the pixel cascade number is not limited by the signal transmission, only depending on the speed of signal transmission.